-
1 valeur limite
предельная величина
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
limit value
A workplace exposure criterion or standard that determines if a facility or building has a concentration of a substance to which most workers can be exposed without harmful or adverse effects. (Source: HEG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > valeur limite
-
2 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
3 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
4 tension limite conventionnelle de contact
допустимое напряжение прикосновения
Максимальное значение ожидаемого напряжения прикосновения, продолжительность воздействия которого не ограничивается при определенных внешних условиях.
[ ГОСТ Р МЭК 60050-195-2005]
[ ГОСТ Р МЭК 60050-826-2009]EN
conventional touch voltage limit
maximum value of the prospective touch voltage which is permitted to be maintained indefinitely in specified conditions of external influences
Source: 826-02-04 MOD
[IEV number 195-05-10]FR
tension limite conventionnelle de contact
valeur maximale de la tension de contact présumée qu'il est admis de pouvoir maintenir indéfiniment dans des conditions d'influences externes spécifiées
Source: 826-02-04 MOD
[IEV number 195-05-10]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension limite conventionnelle de contact
-
5 tension limite conventionnelle de toucher
допустимое напряжение прикосновения
Максимальное значение ожидаемого напряжения прикосновения, продолжительность воздействия которого не ограничивается при определенных внешних условиях.
[ ГОСТ Р МЭК 60050-195-2005]
[ ГОСТ Р МЭК 60050-826-2009]EN
conventional touch voltage limit
maximum value of the prospective touch voltage which is permitted to be maintained indefinitely in specified conditions of external influences
Source: 826-02-04 MOD
[IEV number 195-05-10]FR
tension limite conventionnelle de contact
valeur maximale de la tension de contact présumée qu'il est admis de pouvoir maintenir indéfiniment dans des conditions d'influences externes spécifiées
Source: 826-02-04 MOD
[IEV number 195-05-10]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension limite conventionnelle de toucher
-
6 basse tension
низкое напряжение
-
[IEV number 151-15-03]
низкое напряжение
-
[IEV number 151-15-04]EN
low voltage (1)
low tension (1)
LV (1), abbreviation
voltage having a value below a conventionally adopted limit
NOTE – For the distribution of AC electric power, the upper limit is generally accepted to be 1 000 V.
Source: 601-01-26 MOD
[IEV number 151-15-03]
low voltage (2)
low tension (2)
LV (2), abbreviation
the lowest of two or more voltages in an apparatus or installation
NOTE – An example is the low-voltage winding of a transformer.
[IEV number 151-15-04]FR
basse tension (1), f
BT (1), abréviation
tension électrique de valeur inférieure à une limite adoptée par convention
NOTE – Dans la distribution d'énergie électrique AC, la limite supérieure généralement admise est de 1 000 V.
Source: 601-01-26 MOD
[IEV number 151-15-03]
basse tension (2), f
BT (2), abréviation
la plus basse de plusieurs tensions électriques dans un appareil ou une installation
NOTE – Un exemple est l'enroulement à basse tension d'un transformateur.
[IEV number 151-15-04]
Низкое напряжение
Напряжение, не превышающее значений 1000 В переменного тока и 1500 В постоянного тока.
Под низким напряжением в стандартах Международной электротехнической комиссии (МЭК) понимают любое напряжение переменного тока до 1000 В и постоянного тока до 1500 В включительно. В национальных стандартах, разработанных на основе стандартов МЭК, широко используют понятие «низкое напряжение». Так, например, электроустановка здания в соответствии с требованиями стандартов комплекса ГОСТ Р 50571 «Электроустановки зданий», является низковольтной электроустановкой. ГОСТ Р МЭК 449–96 «Электроустановки зданий. Диапазоны напряжения», введённый в действие с 1 января 1997 г., установил для электроустановок зданий два диапазона номинального напряжения. Напряжения диапазона I соответствуют так называемому сверхнизкому напряжению. Напряжения диапазона II, максимальные значения которых установлены равными 1000 В для электрических систем переменного тока и 1500 В – для электрических систем постоянного тока, соответствуют низкому напряжению.
В стандартах комплекса ГОСТ Р 50030 «Низковольтная аппаратура распределения и управления» установлены требования к низковольтной коммутационной аппаратуре и аппаратуре управления, предназначенной для эксплуатации в электрических цепях переменного тока напряжением до 1000 В и постоянного тока до 1500 В. В стандартах комплекса ГОСТ Р 51321 «Устройства комплектные низковольтные распределения и управления» изложены требования к комплектным низковольтным распределительным устройствам, которые могут иметь номинальное напряжение не более 1000 В переменного тока и не более 1500 В постоянного тока.
Однако в Правилах устройства электроустановок 7-го издания до сих пор все электроустановки неправомерно классифицируют как электроустановки до 1000 В и электроустановки выше 1000 В.
[ http://www.volt-m.ru/glossary/letter/%CD/view/33/]Тематики
- электротехника, основные понятия
- электроустановки
Синонимы
- НН
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > basse tension
-
7 BT
низкое напряжение
-
[IEV number 151-15-03]
низкое напряжение
-
[IEV number 151-15-04]EN
low voltage (1)
low tension (1)
LV (1), abbreviation
voltage having a value below a conventionally adopted limit
NOTE – For the distribution of AC electric power, the upper limit is generally accepted to be 1 000 V.
Source: 601-01-26 MOD
[IEV number 151-15-03]
low voltage (2)
low tension (2)
LV (2), abbreviation
the lowest of two or more voltages in an apparatus or installation
NOTE – An example is the low-voltage winding of a transformer.
[IEV number 151-15-04]FR
basse tension (1), f
BT (1), abréviation
tension électrique de valeur inférieure à une limite adoptée par convention
NOTE – Dans la distribution d'énergie électrique AC, la limite supérieure généralement admise est de 1 000 V.
Source: 601-01-26 MOD
[IEV number 151-15-03]
basse tension (2), f
BT (2), abréviation
la plus basse de plusieurs tensions électriques dans un appareil ou une installation
NOTE – Un exemple est l'enroulement à basse tension d'un transformateur.
[IEV number 151-15-04]
Низкое напряжение
Напряжение, не превышающее значений 1000 В переменного тока и 1500 В постоянного тока.
Под низким напряжением в стандартах Международной электротехнической комиссии (МЭК) понимают любое напряжение переменного тока до 1000 В и постоянного тока до 1500 В включительно. В национальных стандартах, разработанных на основе стандартов МЭК, широко используют понятие «низкое напряжение». Так, например, электроустановка здания в соответствии с требованиями стандартов комплекса ГОСТ Р 50571 «Электроустановки зданий», является низковольтной электроустановкой. ГОСТ Р МЭК 449–96 «Электроустановки зданий. Диапазоны напряжения», введённый в действие с 1 января 1997 г., установил для электроустановок зданий два диапазона номинального напряжения. Напряжения диапазона I соответствуют так называемому сверхнизкому напряжению. Напряжения диапазона II, максимальные значения которых установлены равными 1000 В для электрических систем переменного тока и 1500 В – для электрических систем постоянного тока, соответствуют низкому напряжению.
В стандартах комплекса ГОСТ Р 50030 «Низковольтная аппаратура распределения и управления» установлены требования к низковольтной коммутационной аппаратуре и аппаратуре управления, предназначенной для эксплуатации в электрических цепях переменного тока напряжением до 1000 В и постоянного тока до 1500 В. В стандартах комплекса ГОСТ Р 51321 «Устройства комплектные низковольтные распределения и управления» изложены требования к комплектным низковольтным распределительным устройствам, которые могут иметь номинальное напряжение не более 1000 В переменного тока и не более 1500 В постоянного тока.
Однако в Правилах устройства электроустановок 7-го издания до сих пор все электроустановки неправомерно классифицируют как электроустановки до 1000 В и электроустановки выше 1000 В.
[ http://www.volt-m.ru/glossary/letter/%CD/view/33/]Тематики
- электротехника, основные понятия
- электроустановки
Синонимы
- НН
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > BT
-
8 transformateur de courant pour protection
трансформатор тока для защиты
Трансформатор тока, предназначенный для передачи сигнала измерительной информации на устройства защиты и управления.
[ ГОСТ 18685-73]EN
protective current transformer
a current transformer intended to transmit an information signal to protective and control devices
NOTE – The accuracy class of a protective current transformer is designated by its class index followed by the letter P (standing for "Protection"). The class index gives the limit of the absolute value of composite error at the rated accuracy limit primary current for the class concerned, as a percentage of this current.
[IEV number 321-02-19]FR
transformateur de courant pour protection
transformateur de courant destiné à transmettre un signal d'information à des dispositifs de protection ou de commande
NOTE – La classe de précision d'un transformateur de courant pour protection est désignée par son indice de classe, suivi de la lettre "P" (signifiant "Protection"). L'indice de classe indique la limite supérieure de la valeur absolue de l'erreur composée, au courant limite de précision assigné prescrit pour la classe considérée, en pourcentage de ce courant.
[IEV number 321-02-19]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > transformateur de courant pour protection
-
9 tension limite conventionnelle de contact, UL
условный предел напряжения прикосновения
UL
Максимально допустимое в течение неограниченного времени напряжение прикосновения для установленных условий внешних воздействий, обычно равное 50 В среднеквадратического значения переменного тока или 120 В постоянного тока без пульсаций
[МЭС 826-02-04, измененный].
[ ГОСТ Р 61557-1-2006]EN
conventional touch voltage limit, UL
maximum value of the touch voltage which is permitted to be maintained indefinitely in specified conditions of external influences and is usually equal to 50 V a.c., r.m.s. or 120 V ripple free d.c.
[IEC 61557-1, ed. 2.0 (2007-01)]FR
tension limite conventionnelle de contact, UL
valeur maximale de la tension de contact qu’il est admis de pouvoir maintenir indéfiniment dans des conditions spécifiées d’influences externes et qui est égale habituellement à une valeur efficace de 50 V c.a., ou 120 V c.c. libre d’ondulation
[IEC 61557-1, ed. 2.0 (2007-01)]Тематики
EN
FR
- tension limite conventionnelle de contact, UL
Франко-русский словарь нормативно-технической терминологии > tension limite conventionnelle de contact, UL
-
10 valeur limite du courant de sortie
предельное значение выходного тока
-
[IEV number 314-04-09]EN
limiting value of the output current
upper limit of output current which cannot, by design, be exceeded under any conditions
[IEV number 314-04-09]FR
valeur limite du courant de sortie
valeur supérieure du courant de sortie qui, par conception, ne peut pas être dépassée, quelles que soient les conditions d’utilisation
[IEV number 314-04-09]Тематики
- измерение электр. величин в целом
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > valeur limite du courant de sortie
-
11 appareil à zéro supprimé
прибор с подавлением нуля
-
[IEV number 312-02-03]EN
instrument with suppressed zero
instrument which does not indicate the value of the measurand when it is lower in absolute value to a certain limit
NOTE – "Suppressed zero" can apply to either mechanical zero or electrical zero.
[IEV number 312-02-03]FR
appareil à zéro supprimé
appareil qui ne fournit pas la valeur du mesurande lorsqu’elle est inférieure en valeur absolue à une certaine limite
NOTE – La suppression de zéro peut concerner aussi bien le zéro mécanique que le zéro électrique.
[IEV number 312-02-03]Тематики
- измерение электр. величин в целом
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > appareil à zéro supprimé
-
12 ballast
балласт (в контактной линзе)
Асимметричное распределение массы в контактной линзе.
[ ГОСТ 28956-91]Тематики
Обобщающие термины
EN
FR
балласт
Техническое средство, включаемое между электрической сетью и одной или несколькими разрядными лампами, которое служит, в основном, для ограничения тока ламп(ы) до требуемого значения. Оно может содержать средства для преобразования напряжения и/или частоты питания, коррекции коэффициента мощности и создания самостоятельно или в совокупности со стартером условий, необходимых для зажигания ламп(ы)
[ ГОСТ Р 51317.3.2-99 (МЭК 61000-3-2-95)]
пускорегулирующий аппарат
ПРА
Устройство, включаемое между источником питания и одной или несколькими разрядными лампами, которое за счет индуктивности, емкости или омического сопротивления по отдельности или в их сочетании обеспечивает ограничение тока ламп(ы) до требуемого значения.
Оно может также содержать средства для преобразования напряжения питания и устройства, которые обеспечивают напряжение зажигания и ток предварительного подогрева, препятствуют зажиганию ламп в холодном состоянии, снижают стробоскопический эффект, корректируют коэффициент мощности и подавляют радиопомехи.
[ ГОСТ Р МЭК 60598-1-2011]EN
ballast
unit inserted between the supply and one or more discharge lamps which by means of inductance, capacitance, or a combination of inductance and capacitance, serves mainly to limit the current of the lamp(s) to the required value. It may also include means for transforming the supply voltage and arrangements that help provide starting voltage and pre-heating current
[IEC 62493, ed. 1.0 (2009-12)]FR
ballast
unité insérée entre l’alimentation et une ou plusieurs lampes à décharge qui, via l’inductance, la capacité, ou une combinaison des deux, sert principalement à limiter le courant de la ou des lampes à la valeur requise. Elle peut aussi comporter un transformateur de la tension d’alimentation, et des dispositifs qui permettent de fournir la tension d’amorçage et le courant de préchauffage
[IEC 62493, ed. 1.0 (2009-12)]Тематики
- лампы, светильники, приборы и комплексы световые
Синонимы
EN
FR
Франко-русский словарь нормативно-технической терминологии > ballast
-
13 haute tension
1
высокое напряжение
-
[IEV number 151-15-05]EN
high voltage (1)
high tension (1)
HV (1), abbreviation
voltage having a value above a conventionally adopted limit
NOTE – An example is the set of upper voltage values used in bulk power systems.
Source: 601-01-27 MOD
[IEV number 151-15-05]FR
haute tension (1), f
2
HT (1), abréviation
tension électrique de valeur supérieure à une limite adoptée par convention
NOTE – Un exemple est l'ensemble des tensions les plus élevées utilisées dans les réseaux de production-transport d'énergie électrique.
Source: 601-01-27 MOD
[IEV number 151-15-05]высокое напряжение
-EN
High Voltage
HV
systems with nominal voltage in range above 1 000 V a.c. and up to and including 15 kV a.c.
NOTE This definition differs from the conventional definition.
[IEC/PAS 60092-510, ed. 1.0 (2009-04)]FR
-
Синонимы
- ВН
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > haute tension
-
14 HT
1
высокое напряжение
-
[IEV number 151-15-05]EN
high voltage (1)
high tension (1)
HV (1), abbreviation
voltage having a value above a conventionally adopted limit
NOTE – An example is the set of upper voltage values used in bulk power systems.
Source: 601-01-27 MOD
[IEV number 151-15-05]FR
haute tension (1), f
2
HT (1), abréviation
tension électrique de valeur supérieure à une limite adoptée par convention
NOTE – Un exemple est l'ensemble des tensions les plus élevées utilisées dans les réseaux de production-transport d'énergie électrique.
Source: 601-01-27 MOD
[IEV number 151-15-05]высокое напряжение
-EN
High Voltage
HV
systems with nominal voltage in range above 1 000 V a.c. and up to and including 15 kV a.c.
NOTE This definition differs from the conventional definition.
[IEC/PAS 60092-510, ed. 1.0 (2009-04)]FR
-
Синонимы
- ВН
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > HT
См. также в других словарях:
limit value — ribinė vertė statusas T sritis Standartizacija ir metrologija apibrėžtis Pamatinė ore esančio cheminio ar biologinio agento koncentracijos vertė. atitikmenys: angl. limit value vok. Grenzwert, m rus. предельное значение, n pranc. valeur limite, f … Penkiakalbis aiškinamasis metrologijos terminų žodynas
limit value of water quality parameter — vandens kokybės rodiklio ribinė vertė statusas Aprobuotas sritis vanduo apibrėžtis Didžiausioji arba mažiausioji leidžiamoji vandens kokybės rodiklio vertė per tam tikrą laikotarpį. atitikmenys: angl. limit value of water quality parameter vok.… … Lithuanian dictionary (lietuvių žodynas)
Threshold limit value — The threshold limit value (TLV) of a chemical substance is a level to which it is believed a worker can be exposed day after day for a working lifetime without adverse health effects. Strictly speaking, TLV is a reserved term of the American… … Wikipedia
Threshold Limit Value — The Threshold Limit Value (TLV) of a chemical substance is a level to which it is believed a worker can be exposed day after day for a working lifetime without adverse health effects. Strictly speaking, TLV is a reserved term of the American… … Wikipedia
Threshold Limit Value - Time Weighted Average — Saltar a navegación, búsqueda Threshold Limit Value Time Weighted Average (TLV TWA, Valor Límite Umbral Media Ponderada en el Tiempo). Valor límite ambiental publicado por la A.C.G.I.H. (American Conference of Governmental Industrial Hygienists); … Wikipedia Español
Indicative limit value — In the law of the European Union, indicative limit values, more exactly indicative occupational exposure limit values (IOELVs), are human exposure limits to hazardous substances specified by the Council of the European Union based on expert… … Wikipedia
Threshold Limit Value — Time Weighted Average (TLV TWA, Valor Límite Umbral Media Ponderada en el Tiempo o Telematicamente Limites Umbral). Contenido 1 Definición 2 Conceptos similares 3 Véase también 4 … Wikipedia Español
emission limit value — išmetamųjų teršalų ribinė vertė statusas Aprobuotas sritis aplinkos apsauga apibrėžtis Išmetamųjų teršalų kiekis, išreikštas tam tikrais parametrais, koncentracija ir (ar) lygiu, kurių negalima viršyti per vieną arba kelis laikotarpius.… … Lithuanian dictionary (lietuvių žodynas)
emission limit value — išleidžiamųjų teršalų ribinė vertė statusas Aprobuotas sritis vanduo apibrėžtis Didžiausia leidžiama išleisti teršalų koncentracija ir (arba) didžiausias leidžiamas išleisti teršalų kiekis, kurių negalima viršyti per tam tikrą laikotarpį.… … Lithuanian dictionary (lietuvių žodynas)
emission limit value — didžiausioji leidžiamoji tarša statusas T sritis ekologija ir aplinkotyra apibrėžtis Iš vieno ar kelių taršos šaltinių per laiko vienetą išleistų kenksmingųjų medžiagų kiekis, neviršijantis koncentracijos ribinės vertės. santrumpa( os) DLT… … Ekologijos terminų aiškinamasis žodynas
threshold limit value — (TLV) a value assigned to an industrial chemical by the American Conference of Governmental Hygienists, representing the maximum concentration to which most workers can be repeatedly exposed without adverse health effects … Medical dictionary